At present, the biggest technical problem of LED lighting fixtures is the heat dissipation problem. The LED heat supply and electrolytic capacitors have become the shortcomings for the further development of LED lighting fixtures due to poor heat dissipation. In the luminaire scheme using the LVLED light source, since the LED light source operates at a low voltage (VF=3.2V) and a large current (IF=300-700 mA), the heat is very strong, and the space of the conventional luminaire is narrow, and the heat dissipation of a small area is small. It is difficult to derive heat quickly. Despite the use of a variety of cooling solutions, the results are not satisfactory, becoming a problem with LED lighting fixtures. Looking for easy to use, good thermal conductivity, and low-cost heat sink materials are always working hard. At present, after the LED light source is powered on, about 30% of the electrical energy is converted into light energy, and the rest is converted into heat energy. Therefore, it is a key technology to design the LED light structure as soon as possible to derive so much thermal energy. The heat energy needs to pass heat conduction, heat convection, and heat radiation. Can be distributed. Only by exposing the heat as soon as possible can the cavity temperature in the LED lamp be effectively reduced, so as to protect the power source from working in a long-lasting high temperature environment, in order to avoid premature aging of the LED light source due to long-term high temperature operation. The heat dissipation path of LED lighting fixtures Because the LED light source itself has no infrared rays and ultraviolet rays, the LED light source itself has no radiation heat dissipation function, and the heat dissipation route of the LED lighting fixture can only derive heat through the heat sink closely combined with the LED lamp bead. The heat sink must have the functions of heat conduction, heat convection, and heat radiation. Any radiator, in addition to being able to quickly transfer heat from the heat source to the surface of the radiator, the most important thing is to rely on convection and radiation to dissipate heat into the air. Thermal conduction only solves the heat transfer path, and thermal convection is the main function of the heat sink. The heat dissipation performance is mainly determined by the heat dissipation area, shape, and natural convection strength. Thermal radiation is only an auxiliary function. In general, if the distance from the heat source to the surface of the heat sink is less than 5 mm, then as long as the thermal conductivity of the material is greater than 5, the heat can be derived, and the rest of the heat must be dominated by heat convection. Most LED lighting sources still use low voltage (VF=3.2V), high current (IF=200-700mA) LED lamp beads. Due to the high heat during operation, aluminum alloy with high thermal conductivity must be used. There are usually die-cast aluminum radiators, extruded aluminum radiators, and stamped aluminum radiators. Die-casting aluminum radiator is a kind of technology for pressure casting parts. The liquid zinc-copper-aluminum alloy is poured into the inlet of the die-casting machine, and die-casting is carried out by a die-casting machine to cast a shape-shaped radiator defined by a pre-designed mold. Die-cast aluminum radiators have controllable production costs, and the heat-dissipating fins cannot be made thin, making it difficult to maximize the heat dissipation area. LED lamp radiators commonly used die-cast materials for ADC10 and ADC12. The extruded aluminum heat sink is formed by extruding liquid aluminum through a fixed mold, and then cutting the rod into a heat sink of a desired shape by machining, and the processing cost is high. The extruded aluminum heat sink is shown in Figure 3. The heat dissipating wings can be made a lot of thin, and the heat dissipating area is maximized. When the cooling fins work, the air convection heat is automatically formed, and the heat dissipating effect is better. Common materials are AL6061 and AL6063. The stamped aluminum radiator is stamped and pulled up by the punching machine and the die for the steel and aluminum alloy, so that it becomes a cup-type radiator. The inner and outer periphery of the stamped heat sink is smooth, and the heat-dissipating area is limited due to the wingless. Commonly used aluminum alloy materials are 5052, 6061, 6063. The quality of stamping parts is small and the material utilization rate is high, which is a low-cost solution. The heat conduction of the aluminum alloy heat sink is ideal, and is suitable for the isolated switching constant current power supply. For non-isolated switching constant current power supply, it is necessary to isolate AC and DC, high voltage and low voltage power supply through the structural design of the luminaire, in order to pass CE or UL certification. The plastic aluminum radiator is a heat sink with a heat-conductive plastic aluminum core. The heat-conducting plastic and the aluminum heat-dissipating core are formed on the injection molding machine at one time, and the aluminum heat-dissipating core is embedded, and it is required to be machined in advance. The heat of the LED lamp bead is quickly transmitted to the heat-conducting plastic through the aluminum heat-dissipating core, and the heat-conductive plastic uses its multi-wing to form air convection heat, and uses its surface to radiate part of the heat. The plastic-coated aluminum heat sink generally uses the original color of the heat-conductive plastic white and black, and the black plastic plastic-coated aluminum heat sink has a better radiation heat dissipation effect. Thermally conductive plastic is a thermoplastic material. The fluidity, density, toughness and strength of the material are easy to be injection molded. It has good resistance to cold and heat shock cycles and excellent insulation performance. Thermally conductive plastics have better emissivity than ordinary metallic materials. The thermal conductive plastic density is 40% smaller than that of die-cast aluminum and ceramics. The same shape of the heat sink, the weight of the plastic-coated aluminum can be reduced by nearly one-third; compared with the all-aluminum heat sink, the processing cost is low, the processing cycle is short, and the processing temperature is low; The finished product is not easy to break; the customer-supplied injection molding machine can design and produce the differentiated shape of the lamp. The plastic-coated aluminum radiator has good insulation performance and is easy to pass the safety regulations.
Face roller Veneer Dryer machine is one of the roller veneer dryers . Face veneer dryer machine quality requirements are more higher than normal roller veneer dryer . The material is stainless steel , and the distance between two rollers is 140mm . the face veneer can be 0.3mm thinnest.
Drying Line,Face Veneer Dryer,Thin Veneer Dryer,Face Veneer Dryer Machine
Shandong Shine Machinery Co.,Ltd , https://www.shinewoodmachine.com